Welcome to WIFI Antennas

Register now to gain access to all of our features. Once registered and logged in, you will be able to contribute to this site by submitting your own content or replying to existing content. You'll be able to customize your profile, receive reputation points as a reward for submitting content, while also communicating with other members via your own private inbox, plus much more! This message will be removed once you have signed in.

Admin

PCB Panel Antenna

These printed circuit board (PCB) antennas are perfect for high performance optimized antennas in a small package. These antennas are great for expanding your wireless network and improving your broadcasting or receiving stations.

 

Antena Planar Desenho 1.jpg

Antena Planar Disenho 2.jpg

Medidas nuevas.jpg

screenshot_3206.jpg

Share this post


Link to post
Share on other sites

 my simulation it"s with galvanized sheet metal, not PCB...

59.jpg

screenshot_3207.jpg

1 person likes this

Share this post


Link to post
Share on other sites
On 21/12/2016 at 11:30 AM, Admin said:

These printed circuit board (PCB) antennas are perfect for high performance optimized antennas in a small package. These antennas are great for expanding your wireless network and improving your broadcasting or receiving stations.

 

Antena Planar Desenho 1.jpg

Antena Planar Disenho 2.jpg

Medidas nuevas.jpg

screenshot_3206.jpg

hi admin. do you have the reflector and spacing measurements? the pcb must be of some special type? Can you recommend any other antenna with similar performance using a pcb of less than 100x100mm?

many thanks!

Share this post


Link to post
Share on other sites

,,,hi buddy...!!!  

,,,spacing measurements = 4,5mm,material PCB=FR4 #1,5mm

,,,an antenna with 100x100mm reflector will have a much smaller directional gain and in any case it cannot have 4 patches as vibrators...!!!

,,,and I don't think it was necessary to post all my images above....!!!

Share this post


Link to post
Share on other sites

,,, where the soldering is seen ... !!!!

Share this post


Link to post
Share on other sites

is the screw metal or plastic?

and is it possible to make this in galvanized steel?

Edited by Eric

Share this post


Link to post
Share on other sites

,,,with 2 screw metal ...!!!

,,,it is also possible with galvanized sheet metal, but with other dimensions...!!!

,,,my simulation above is like that...!!!

Share this post


Link to post
Share on other sites
On 9/6/2020 at 8:47 PM, DeepBlueSea said:

Where SMA Port brother ? 

How to make it . If use double sma port??

Share this post


Link to post
Share on other sites

,,, what will you say "double sma port"...???

,,,, there is only one port....!!!!

Share this post


Link to post
Share on other sites
8 hours ago, Admin said:

,,, what will you say "double sma port"...???

,,,, there is only one port....!!!!

I think he wants it to be MIMO 2x2 (90 degrees ports...)

Share this post


Link to post
Share on other sites
On 6/14/2020 at 1:49 PM, DeepBlueSea said:

How to make it . If use double sma port??

if you want mimo for that  just search here i'm sure you'll find one that'll suits your preference..

Share this post


Link to post
Share on other sites

 ,,,for cutting aluminium sheet with  CNC  machine , must to be other dimensions.!!!

Share this post


Link to post
Share on other sites
6 minutes ago, Techd said:

do u have that measurements ? for aluminium sheet kindly advise 

,,,for which the antenna...???

Share this post


Link to post
Share on other sites

any wifi 2.4ghz antenna which has higer range cover for 1km and also has the speed 

because some wifi antenna have range but don't have speed even if the connected network has good wifi speed.

i believe you will suggest me the best antenna with its cnc cutting detailed drawing for aluminium sheet so that i can extended my wifi signal and simultaneously receive same speed at the extended area. 

 

kindly help since last 2 days i am requesting you plz help 

Share this post


Link to post
Share on other sites

,,, you can try to do that...!!!!

,,, why not search on this forum, you can find what interests you...!!

Share this post


Link to post
Share on other sites

,,,hi buddy...!!

,,,14,5 dBi,reflector sizes=1x240x240 mm,PCB=FR4#1,5 mm, h-4,5 mm

,,, but please, post a single image, not all are needed...!!!

Share this post


Link to post
Share on other sites
2 hours ago, Admin said:

,,, selam dostum ... !!

,,, 14,5 dBi, reflektör boyutları = 1x240x240 mm, PCB = FR4 # 1,5 mm, h-4,5 mm

,,, ama lütfen, tek bir resim gönderin, hepsine gerek yok ... !!!

Thank You.

Share this post


Link to post
Share on other sites
2 hours ago, Admin said:

,,, selam dostum ... !!

,,, 14,5 dBi, reflektör boyutları = 1x240x240 mm, PCB = FR4 # 1,5 mm, h-4,5 mm

,,, ama lütfen, tek bir resim gönderin, hepsine gerek yok ... !!!

Is the reflector galvanized sheet steel or aluminum

Share this post


Link to post
Share on other sites

If the relector is connected to GND of cable then is better if is of aluminum

Share this post


Link to post
Share on other sites

 

On 12/21/2016 at 9:38 PM, Admin said:

my simulation it"s with galvanized sheet metal, not PCB...

I did a simulation using FR4 as vibrator and 0.5 mm alluminium as reflector and the efficiency is just bad. maybe some modification on vibrator dimensions is needed.

14 dbi panel antenna 2.4 v1.5 R1.cst

1 person likes this

Share this post


Link to post
Share on other sites

,,, pay attention to the port...

screenshot_2714.jpg

screenshot_2715.jpg

1 person likes this

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!


Register a new account

Sign in

Already have an account? Sign in here.


Sign In Now