Welcome to WIFI Antennas

Register now to gain access to all of our features. Once registered and logged in, you will be able to contribute to this site by submitting your own content or replying to existing content. You'll be able to customize your profile, receive reputation points as a reward for submitting content, while also communicating with other members via your own private inbox, plus much more! This message will be removed once you have signed in.

clanon

Raytron 16dbi patch

38 posts in this topic

Raytron 16dbi & 19dbi mod

 

Hi , guys it would be nice if some generous soul simulate this one...

The original is 6 elements over 0.787 ptfe , 2.1 dielectric constant...


(Фольгированные материалы фирмы NELTEC (Франция)
NELTEC — новое название фирмы METCLAD. 
Материалы предназначены для использования в качестве подложек в СВЧ-устройствах.

Материалы имеют нормированную диэлектрическую постоянную, низкий уровень диэлектрических потерь и уменшенную толщину слоя меди.

Основные параметры: 

Толщина диэлектрика: 0.127, 0.254, 0.508, 0.762, 0.787, 1.270, 1.524, 1.575, 3.175 мм 
Диэлектрическая проницаемость (на частоте 10 ГГц): 2.17

 

Antenna_3.jpg

Panel_16dBi.pdf

Antenna_assemble_2.jpg

Edited by clanon

Share this post


Link to post
Share on other sites

Clanon, you're from Argentina and you speak Russian...???
,,, please write in English ... !!!

1 person likes this

Share this post


Link to post
Share on other sites

OK , "dude" ...already built it on a notebook ABS cover...with aluminum foil...CST simulation would be great to fine tunning it...

PD: I'm NOT getting 16dbi and a lot of VSWR

Share this post


Link to post
Share on other sites

ABS should be like 2.8 of dielectric constant and 1.5 mm width ...try to keep 5mm to aluminum reflector inside , but it's tricky...not a lot of space

some wifi cards don't like it so it must be high VSWR...channels  from 1 to 11 all show up...poor signal though...

52051042_343452753175979_3941565528480415744_n.jpg

Edited by clanon

Share this post


Link to post
Share on other sites

,,,well, the reflector where is ... ???

1 person likes this

Share this post


Link to post
Share on other sites

inside 

bigger than patchs and close to 4mm or so the screws touch it on the current centers of the patch

 

Share this post


Link to post
Share on other sites

Clanon, you can put the dimensions to it...???

 

screenshot_234.jpg

screenshot_235.jpg

1 person likes this

Share this post


Link to post
Share on other sites

here's the model...not exact just  taken from that picture...

can't make it dance though...

 

Maybe my settings are wrong for the solver... i tried waveguide and discrete port...TO NO AVAIL

 

raytron 16dbi.cst

Edited by clanon

Share this post


Link to post
Share on other sites

54 by 46 mm each Patch...i think...

Edited by clanon

Share this post


Link to post
Share on other sites

,,,try to import a SMA port from this forum...

screenshot_245.jpg

1 person likes this

Share this post


Link to post
Share on other sites

some doubt about INTERSECTIONS...how its supposed to go...

 

Share this post


Link to post
Share on other sites

... something like that ... !!!

 

 

47.jpg

Anyway, something is wrong ...

 

 

48.jpg

1 person likes this

Share this post


Link to post
Share on other sites

try with teflon ...2.1 dielectric constant...Original material ...close to 0.7...(0.762, 0.787mm)

 

PD: I was gettin LOTS of APs...but too litle signal... less than -62dbm...and a bunch with more than -

 

"Foil materials from NELTEC (France)
NELTEC is the new name of the company METCLAD.
The materials are intended to be used as substrates in microwave devices.

The thickness of the dielectric: 0.127, 0.254, 0.508, 0.762, 0.787, 1.270, 1.524, 1.575, 3.175 mm
The dielectric constant (at a frequency of 10 GHz): 2.17 ... 3.48
Copper layer thickness: 5, 9, 12, 18, 35, 70, 105 microns
Sheet size: 305x457, 406x457, 457x610 mm "

полоска.GIF

Share this post


Link to post
Share on other sites

It SHOULD have one BIG LOBE...in the CENTER (16dbi) and some smaller ones around...IMHO

“Having carefully examined the cable entry point in the photos of the“ original ”, I came to the conclusion that there is not a“ bare ”microstrip, but something like a“ coplanar waveguide. ”Therefore, I provided for such an“ earthen ”polygon at the input

 

 

Share this post


Link to post
Share on other sites

..., only in English, please...!!!

1 person likes this

Share this post


Link to post
Share on other sites

getting there...RE-modeled...

i'm gonna work on the coplanar waveguided thingy...now...

Sin título.jpg

Share this post


Link to post
Share on other sites

Radiation efficiency seems fine... vswr must be the problem...

Sin título.jpg

Share this post


Link to post
Share on other sites

YUP...it's like they're "Forcing" the wave to make a 90 DEGREES through the FEEDING LINE...IMHO...(it must be important) I'll keep you informed if i have success...to 15 or 16dbis...

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!


Register a new account

Sign in

Already have an account? Sign in here.


Sign In Now