Welcome to WIFI Antennas

Register now to gain access to all of our features. Once registered and logged in, you will be able to contribute to this site by submitting your own content or replying to existing content. You'll be able to customize your profile, receive reputation points as a reward for submitting content, while also communicating with other members via your own private inbox, plus much more! This message will be removed once you have signed in.

Admin

Helix Antenna

59 posts in this topic

A method to improve the gain of axial-mode helical antenna is proposed.

This method involves a parasitical circular metal disk,which is installed on the front of general axial-mode helical antenna and is apart from the helical line. A circular current whose phase lags behind that of helical line current appears,which brings a more concentrated radiation field. Consequently,the antenna gain is improved, Based on the simulation results,an antenna array model fed independently is proposed.This model gives an excellent explanation of the radiation characteristic of helical antenna, Both the simulation and experiment results show that for obtaining the same gain,the antenna length in this new method is only 71% of that in traditional helical antenna.The reduction of antenna length favors the miniaturisation of antenna.

In addition, this method has a little effect on the bandwidth of antenna, so it can be widely used in the design of helical antenna element and array.

 

82.jpg

90.jpg91.jpg

96.jpg

screenshot_2383.jpg

2 people like this

Share this post


Link to post
Share on other sites

This type of helical antennas with a parasitic element directory is used for remote control of drones

 

img_7111.jpg

img_7104.jpg

img_7099.jpg

 

 

restinpeace1.jpg

Share this post


Link to post
Share on other sites

Can this disk be applied to longer helical antennas (2 wavelength) and @ lower frequency? (EG 430 MHz)??

thanks

 

Share this post


Link to post
Share on other sites
2 hours ago, Andrew77 said:

Can this disk be applied to longer helical antennas (2 wavelength) and @ lower frequency? (EG 430 MHz)??

thanks

 

Yes, this parasitic disc can be applied but only at helical antenna  with 3...5 coils or at least reduced by 70-71%.!

Share this post


Link to post
Share on other sites
9 hours ago, antenna_kid said:

Hi, 
has you any design files how to make such antenna ?
I would like to try my skills :)

 

which antenna?

Share this post


Link to post
Share on other sites
On 4.10.2016 at 1:30 PM, Admin said:

 

90.jpg

 

96.jpg

 

interested in such antenna. Made helicals for 5.8Ghz and 2.4 ghz. they are good but long. Helix with parastic element is what i've looked for.
This helicals are so short, that i would like to try make a 2x2 array.

Share this post


Link to post
Share on other sites

Hi, yup. I'm DIY fan. Love drones, but making things gives me more fun. I've made small CNC, 3D printer. Just love DIY.

2 people like this

Share this post


Link to post
Share on other sites

,,,and a helix much simpler...

bignose_07.jpg

bignose_01-tile.jpg

1 person likes this

Share this post


Link to post
Share on other sites

I am new to this forum.  Impressive work here.

I love it.  I would love to try this one..where could I get the dimensions/original research?  That coil spacing/angle is impressive.  

I have used the parasitic disk concept successfully as seen in the pics.  3d printed construction for accuracy.  Inset wire grove and parasitic standoff.  They are much more compact.  I use them on my 2.4 ghz RC transmitter with cp biquad on the receiving end. Massively improved range, but more importantly no dropouts or fly-aways.

0411180055_HDR.jpg

2 people like this

Share this post


Link to post
Share on other sites

,,,hi buddy...!!!

"impressive, did you make these helix antennas ...?

Share this post


Link to post
Share on other sites

Yes, went through a few iterations on the 3d print/construction. Just dialed (range tested on ground and in air) them in last week.  11.3 deg on the coil. In practice the disk really seems to punch the signal through...no drop outs.

 

Share this post


Link to post
Share on other sites

ok, from where did you get this helix geometry...??

 

 

 

Share this post


Link to post
Share on other sites

That is the research I used to construct them.  Used fusion 360 design and print in ABS.  Unfortunately, it does not address  design parameters...just concepts.  I would like to apply it to other frequencies, but it would be impossible to experimentally determine parasitic disk size/distance.  I do not have test equipment or simulation software.

Is there any free online simulation software available similar to what you used above?   Looks expensive.  Thank you for the help.

Share this post


Link to post
Share on other sites

Thank you. I will have to get this on my older PC, as I currently use a Mac.

I would like to try a 1x2 array with the 3 turn I am using shown above.  What distance would I use?  or what equation will determine the minimum distance between coils (multiples of wavelength)? Reflectors 0413180103.jpg to edge sounds too easy.

I also applied this to a 3 turn at 5.8 ghz.  

 

0415181308.jpg

0415181309.jpg

Share this post


Link to post
Share on other sites

...the minimum distance between coils = 0,62*lambda ( wavelength )

....the bestt distance between coils = 0,8-0,9*lambda ( wavelength )

Share this post


Link to post
Share on other sites

Fantastic..I will give it a go.  Thank you so much for actually replying and fast!

In your above example using tape rather than wire...I would like to use tape rather than wire, what design adjustment will I need to make.  For example I used 2mm wire on the 2.4...6mm tape ok?

Share this post


Link to post
Share on other sites

BTW, the distance between coils..from the outer edge of the coils, right?  Not the centers..

Share this post


Link to post
Share on other sites

,,,from center to center coils...

0,025*lambda = tape

 

Share this post


Link to post
Share on other sites

I have been working on feeding my helical from the center of the coil and using a rectangle impedance matching stub.  I am not sure how to account for the length leading to the center feed (1/2 radius of coil).  

Example: 3 turn helical + coil radius feed= Frequency change?

Also, do I use the same impedance matching stub size when feeding from the center?  I hope I explained myself correctly.  Thank you.

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!


Register a new account

Sign in

Already have an account? Sign in here.


Sign In Now