Welcome to WIFI Antennas

Register now to gain access to all of our features. Once registered and logged in, you will be able to contribute to this site by submitting your own content or replying to existing content. You'll be able to customize your profile, receive reputation points as a reward for submitting content, while also communicating with other members via your own private inbox, plus much more! This message will be removed once you have signed in.

Sign in to follow this  
Followers 0
Admin

MiMo 4G Antenna

36 posts in this topic

After sgser's project...

4g_mimo_panel_lte2600_15dBi.jpg

with his simulation vman ...

4GsgserOV.jpg

4GsgserSize.jpg

4Gstep2FF.jpg

and the practical execution of starik...

DS2-1.jpg

I have optimized this achievement...

4patrat_01.jpg

4patrat_02.jpg

4patrat_03.jpg

4patrat_04.jpg

4patrat_05.jpg

4patrat_06.jpg

4patrat_07.jpg

Share this post


Link to post
Share on other sites

,,, and here are some constructive details ...

4patrat_01.jpg

4patrat_02.jpg

4patrat_03.jpg

4patrat_04.jpg

4patrat_05.jpg

1 person likes this

Share this post


Link to post
Share on other sites

Это метал или что?

Можно Ф6 Cu ???.

Хочу собрать, понравилась.

Edited by starik0

Share this post


Link to post
Share on other sites
13 hours ago, starik0 said:

Это метал или что?

Можно Ф6 Cu ???.

Хочу собрать, понравилась.

Yes метал,,,Можно Ф6 Cu...!!!

Бортик NO...!!!  

"But I think it would be better...Бортик=30mm

93.jpg

Share this post


Link to post
Share on other sites

Очень хорошо!

Есть еще вопрос. У меня метал для рефлектора 0.85 , требуется под CMA подложить и довести до 1.0 мм.

А у антенны с бортиками есть размеры? Очень красивая!!!

 

Very good!

There is another question. I have metal for a reflector of 0.85, it is required to enclose under CMA and bring it up to 1.0 mm.

Does the antenna with the sides have dimensions? Very beautiful!!!

 

Share this post


Link to post
Share on other sites

Well, it looks like it works on  2,442GHz and 4G...with an insulation between ports, very good (<-45)...!!!

my4x4_01.jpg

my4x4_02.jpg

my4x4_03.jpg

my4x4_04.jpg

my4x4_05.jpg

my4x4_06.jpg

my4x4_07.jpg

 

The vibrators have a T-shaped puncture and rounded corners...

my4x4_01.jpg

Share this post


Link to post
Share on other sites

And the sizes of patches, both antennas are the same ???
Began to mark up, it's easier to cut 8 pieces at once, for both antennas.
In four do T.

Share this post


Link to post
Share on other sites

Good, soon I will post all the dimensions of the antenna...!!!

Share this post


Link to post
Share on other sites

Вот собрал кучку.

Пятой не хватает жду!

 

4-п1.jpg

4-п.jpg

4-п2.jpg

4-п4шт.jpg

1 person likes this

Share this post


Link to post
Share on other sites

При сборке сложно выдержать 1,5 мм от линий до рефлектора, линии тоненькие трясутся.

4-п11.jpg

Возможно смоделировать с линиями на двух стороннем RF4  ??

Edited by starik0
1 person likes this

Share this post


Link to post
Share on other sites
20 minutes ago, starik0 said:

Возможно смоделировать с линиями на двух стороннем RF4  ??

,,, why double-coated FR4 ... ??

Share this post


Link to post
Share on other sites

Одна сторона рефлектор, вторая линия связи, как раз 1.5мм.

Расстояние будет всегда точно.

 

One side of the reflector, the second line of communication, just 1.5mm.

The distance will always be exact.

 

Share this post


Link to post
Share on other sites

OK, I will try to do this .... !!!
"but here in the forum, there is such an antenna,,,!!!

 

imagoe.jpg

Share this post


Link to post
Share on other sites

Если про Китайскую, то там патчи печатные.

Я про печатные линии связи, а патчи обычные на стойках диаметром 6 мм, 

Патчи своими, (как правильно назвать), отогнутыми конусами, припаять к линиям связи.

Share this post


Link to post
Share on other sites

Yes, it is not MiMo antenna but it can be done ,,, !!!

1 person likes this

Share this post


Link to post
Share on other sites

Буду весьма признателен !!!

А, Вашу пока не нашел?

Edited by starik0

Share this post


Link to post
Share on other sites

MIMO 4G ???
At the moment I can do and experience in the village.
I was interested in the antenna on a two-way RF4, I have a piece of 1.5 and 2.0,
but it is necessary 4G.
Internet in my summer YOTA, it is attached to him.

Do these two antenna patches on the center are also fixed?

02-RF4.jpg

01-RF4.jpg

On this you can link where to place, look more closely?

Edited by starik0

Share this post


Link to post
Share on other sites

Описание синий  4G я нашел, а где про желтую описание?

К сожалению я не знаю где используется круговая поляризация, к моей YOTA надо 4G MIMO, так я могу испытать в работе.

21 hours ago, Admin said:

Yes, it is not MiMo antenna but it can be done ,,, !!!

Это Вы писали, можно значит смоделировать, для 4G MIMO,???

 

 

Share this post


Link to post
Share on other sites

Что легче смоделировать:

1. синюю или желтую в 4G MIMO.

02-RF4.jpg01-RF4.jpg

2. Или у этой панели линии связи сделать на RF4  (1,5 мм или 2.0 мм)

4-пат.jpg

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!


Register a new account

Sign in

Already have an account? Sign in here.


Sign In Now
Sign in to follow this  
Followers 0