Welcome to WIFI Antennas

Register now to gain access to all of our features. Once registered and logged in, you will be able to contribute to this site by submitting your own content or replying to existing content. You'll be able to customize your profile, receive reputation points as a reward for submitting content, while also communicating with other members via your own private inbox, plus much more! This message will be removed once you have signed in.

Admin

PETRA-9 MIMO 4x4 Unibox-2

Petra-9 MIMO 4x4 Unibox-2 is a 3G/4G antenna combined with a spacious sealed box (Unibox-2/Unibox-2L) in which you can place an LTE modem with support for MIMO 4x4 technology or two modems with support for MIMO 2x2 technology. The antenna is equipped with reliable connectors-SMA-male (50 ohms). Antenna adapters for connecting LTE modems are not included. The modem communicates with an indoor PC or router via a USB extension cable (USB 2.0).

If the router is installed inside the box, the antenna can be equipped with a sealed PG-7 or RJ-45 pin (instead of a USB extension cable)

Electrical characteristics of the PETRA-9 MIMO 4x4 UniBox-2 antenna

Operating frequency range, MHz 1700÷2700

Gain factor, dBi 8,5÷10

Bottom width in the H-plane, deg 59÷82

Bottom width in the E-plane, deg 35÷57

Side lobe level, max -7 dB

Decoupling between ports in the operating range, not less than 25 dB

Input impedance, Ohms 50

SWR in the operating frequency range at the inputs, max. 1,5

Permissible power, W 10

Slope of polarization of received / emitted waves -45°/+45°(X-pol)

Mechanical characteristics

Weight of antenna, mount, box, extension cable g 1900

Bracing

mast diameter 20-52 mm

Operating temperature range -60°C to +80°C

Overall dimensions without mounting, m 0, 24x0, 24x0, 1

Permissible wind speed, m / sec 25

Connectors

4 x SMA-male

Material of the protective cover -Polycarbonate+ABS

Antenna Material -Galvanized steel, brass

Mounting material steel / Polycarbonate+ABS

 

screenshot_150.png

screenshot_151.png

screenshot_152.png

screenshot_153.png

1 person likes this

Share this post


Link to post
Share on other sites
28 minutes ago, Antenna gun said:

please show me how to make them

,,, okay, I will try to do a simulation with this antenna...!!!

2 people like this

Share this post


Link to post
Share on other sites
On 04.06.2021 at 0:21 PM, Antenna gun said:

please show me how to make them

An approximate model of one element without exact dimensions and optimization.

Only the principle of construction.

 

1123.png

1 person likes this

Share this post


Link to post
Share on other sites

,,, the place of these antennas is not here, try another suitable place...!!!

Share this post


Link to post
Share on other sites

,,, and from the front ... ??? ,,, this is Bester antenna ... ??

Share this post


Link to post
Share on other sites

,,, what does it look like from the front .... !!!

Bester...

screenshot_572.jpg

Share this post


Link to post
Share on other sites

,,, well then, if you have a sample why not do a simulation with it ... ??? !!

Share this post


Link to post
Share on other sites
1 hour ago, Admin said:

,,, well then, if you have a sample why not do a simulation with it ... ??? !!

I don't have this antenna. I can only roughly predict the dimensions. Above, I laid out the estimated modeling, but it seemed to you not interesting. I adjusted the dimensions to good results at 75 ohms.

75.jpg

 

I drew a 50 Ohm model in the original design. And played around with the size a bit. There is a reserve for tuning. I think I can get results like the 75 ohm option or better.

50.jpg

 

 

1 person likes this

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!


Register a new account

Sign in

Already have an account? Sign in here.


Sign In Now