Welcome to WIFI Antennas

Register now to gain access to all of our features. Once registered and logged in, you will be able to contribute to this site by submitting your own content or replying to existing content. You'll be able to customize your profile, receive reputation points as a reward for submitting content, while also communicating with other members via your own private inbox, plus much more! This message will be removed once you have signed in.

lrg

AX-2600 OFFSET 75 MIMO 2x2 офсетный облучатель 4G

58 posts in this topic
17 hours ago, Admin said:

,,,well Irg, but for which frequency do you want...!!!

In this topic of course same on 2600 MHz . and it would be very smart for two frequencies of 2600 and 1800 MHz.under the 75 Ohm cable

Share this post


Link to post
Share on other sites

Here are the dimensions posted by user  Chilanzar2, for the 1.8GHz frequency...

2.jpg

4.jpg

 

5.jpg

and the simulation of this antenna...

screenshot_124.png

2 people like this

Share this post


Link to post
Share on other sites

Thank you so much. it's an important frequency for me.I have already started manufacturing          : -) .in General, it would be interesting to know the size of the irradiator at 2.6 MHz

1 person likes this

Share this post


Link to post
Share on other sites

"Irg, I will soon adapt the antenna for this frequency....!!!!

1 person likes this

Share this post


Link to post
Share on other sites
On 19.06.2018 at 2:26 PM, Admin said:

,,,well Irg, but for which frequency do you want...!!!

Sorry I hurried and did not even ask about the thickness of the metal patches in this irradiator

Share this post


Link to post
Share on other sites
37 minutes ago, lrg said:

Sorry I hurried and did not even ask about the thickness of the metal patches in this irradiator

What is the thickness of the metal used in this feed?

Share this post


Link to post
Share on other sites
On 7/25/2018 at 10:05 AM, lrg said:

What is the thickness of the metal used in this feed?

I think Chilanzar could inform you best...!!!

" it might be 0.5mm...!!!

Share this post


Link to post
Share on other sites
1 hour ago, Admin said:

I think Chilanzar could inform you best...!!!

" it might be 0.5mm...!!!

Chilanzar? Where can I find it?

Share this post


Link to post
Share on other sites

,,, here, on this forum ... !!!

"chilanzar2"

Share this post


Link to post
Share on other sites

тольщина патчей - 0.7мм.

Но, мне не нравится этот облучатель. Я ищу 1700-2200 MIMO

 

the thickness of the patches is 0.7mm.
But, I do not like this irradiator. I am looking for 1700-2200 MIMO

1 person likes this

Share this post


Link to post
Share on other sites
On 7/28/2018 at 6:12 AM, chilanzar2 said:

тольщина патчей - 0.7мм.

Но, мне не нравится этот облучатель. Я ищу 1700-2200 MIMO

Подскажите толщину стоек. Я нашлол от приборов.чтобы меньше их переделывать. Нет поблизости токаря.

 

Tell me the thickness of the racks. I found it from devices. To reduce them less. There is no nearby turner.

1532929342598-900928847.jpg

Tell me the thickness of the racks. I have these.they probably will be able to come up with some small alterations.there's no lathe in the vicinity.:-)

Share this post


Link to post
Share on other sites

on the irradiator Antex is used 6mm. I use 4.7 mm. other I have no...I buy on aliexpress

Share this post


Link to post
Share on other sites
38 minutes ago, chilanzar2 said:

on the irradiator Antex is used 6mm. I use 4.7 mm. other I have no...I buy on aliexpress

It is clear you used computer racks on which the motherboard is installed.

stoyki-dlya-materinskoy-platy.jpg

Share this post


Link to post
Share on other sites

нужного размера очень тяжело найти в компьютерах - поэтому лучше искать и покупать на алиэкспресс

the right size is very hard to find in computers - so it's better to look and buy on aliexpress
  Like this

Share this post


Link to post
Share on other sites

,,,good, another constructive form of this antenna, with built-in modem...

2000box3-600x600.jpg

2000box4-600x600.jpg

2000box5-600x600.jpg

Share this post


Link to post
Share on other sites

Chil, I think it's all M3 screw, but with a step more than 0.5mm (0.6 ... 0.7mmm))

Share this post


Link to post
Share on other sites

this is the American standard. we don't have these nuts. No in Europe.

Share this post


Link to post
Share on other sites
On 14/11/2017 at 1:29 AM, lrg said:

6881040.jpg

Dimensions are not clear here, reflector to the first patch 4mm.. reflector to the 2nd patch 6mm.. so from the 1st patch to the 2nd patch only 2 mm? it's seems more

Share this post


Link to post
Share on other sites

,,, Kledi,this is not the place of this antenna, move it...!!!

 I will delete this post...!!!

Share this post


Link to post
Share on other sites
7 minutes ago, Admin said:

,,, Kledi,this is not the place of this antenna, move it...!!!

 I will delete this post...!!!

7 minutes ago, Admin said:

,,, Kledi,this is not the place of this antenna, move it...!!!

 I will delete this post...!!!

On 14/11/2017 at 1:29 AM, lrg said:

6881040.jpg

 

 

 

Yes admin this is the offset antenna dimension, watch the first page..

Share this post


Link to post
Share on other sites

,,, oh, yes, you're right, excuse me ... !!

,,,these are the dimensions...!!!

d4.jpg

 

d5.jpg

 I think I will recalculate this antenna for optimization.

Share this post


Link to post
Share on other sites

Thank you! I have only 1mm galvanized steel, Will It work? I cant find 0.5mm here in my town

Share this post


Link to post
Share on other sites

,,,yes, you can use 1mm thick...!!!

,,, try to delete the double images above...!!!

Share this post


Link to post
Share on other sites

Can we have a mimo 1800-2600 feed offset antenna  please ?

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!


Register a new account

Sign in

Already have an account? Sign in here.


Sign In Now