Welcome to WIFI Antennas

Register now to gain access to all of our features. Once registered and logged in, you will be able to contribute to this site by submitting your own content or replying to existing content. You'll be able to customize your profile, receive reputation points as a reward for submitting content, while also communicating with other members via your own private inbox, plus much more! This message will be removed once you have signed in.

lrg

AX-2600 OFFSET 75 MIMO 2x2 офсетный облучатель 4G

58 posts in this topic

 AX-2600 OFFSET 75 Ohm MIMO 2x2 offset irradiator 4G.
Operating frequency range, MHz 2500-2700

Own gain, dBi 9-10

the Resulting gain and beamwidth at-3dB level at different diameters offset parabolic antenna (at a frequency of 2000МГц)

0.55 m 21dBi .
0.6 m 22dBi .
0.9 m 25dBi .
1.3 m 29dBi .
1.5 m  30dBi.

 

6881036.jpg6881037.jpg

6881040.jpg6882414.jpg

1 person likes this

Share this post


Link to post
Share on other sites
11 hours ago, lrg said:

15.3mm center of the bolts.

,,,it"s important the distance between patches and the reflector....!!! which are ...?

Share this post


Link to post
Share on other sites

check it in the program . under the first patch the 2 nuts, then the 3 nuts. Just the height of the nut 2.4 mm

Share this post


Link to post
Share on other sites

Not much kick, took off as I could First size the reflector 4mm, 6mm second.

Share this post


Link to post
Share on other sites

Check it out in the program . the reflector 2 nuts, then the 3 nuts. the height of the nut 2.4 mm

Share this post


Link to post
Share on other sites

Yes you are right, tried on the first size in the corners diagonally, there's a helicopter which from one side 4mm the other 5.3 on the second size of the dispersion was measured at the corners of a diagonal of 7 and 8 mm So I unfortunately spoil the work of the developers Krivorukov collectors.

1 person likes this

Share this post


Link to post
Share on other sites

When I have time, I will do a simulation on this antenna ... !!!
,,, but tell me the dimensions of the square adapter .... !!!

,,,this...

80.jpg

Share this post


Link to post
Share on other sites

square sealing is also a curve. from one angle 8 mm with another 9mm.

1 person likes this

Share this post


Link to post
Share on other sites

,,,no,,,0,5mm...but if you want I turn it into 1 mm

Share this post


Link to post
Share on other sites

there's no need. prsche people find galvanized sheet 0.5

Share this post


Link to post
Share on other sites

I do not do graphics, but more practice and do not advise at such high frequencies 4G to use 75 Ohm 

Share this post


Link to post
Share on other sites

Irradiator AX-2600 OFFSET  2x2 MIMO in the set with offset mirror antenna (not included) designed to increase range of 4G modems the range of 2.5-2.7 GHz . Mirror antenna with feed significantly improves the quality of communication at the boundaries of the service area operators 4G. . Antenna connector with short circuit DC current between the outer and inner conductors.The irradiator has two inputs, corresponding to orthogonal polarizations of the radiated signal. The original design of the antenna feed provides high isolation between inputs in a wide frequency band.  

2600Offset_75_MIMO22.JPG

IMG_20180608_222053.jpg

IMG_20180608_222106.jpg

 

10.jpg

2 people like this

Share this post


Link to post
Share on other sites
On 6/9/2018 at 0:26 PM, Admin said:

Irradiator AX-2600 OFFSET  2x2 MIMO in the set with offset mirror antenna (not included) 

IMG_20180608_222053.jpg

I want to make this irradiator in iron. Can the size of this radiator. Thanks

Share this post


Link to post
Share on other sites

Irg, I do not have the original size, but I will try ... !!!

 

57.jpg

Share this post


Link to post
Share on other sites
On 18.06.2018 at 9:12 AM, Admin said:

Irg, I do not have the original size, but I will try ... !!!

 

57.jpg

Thanks. I will be grateful for the exact dimensions of the irradiator. I would like to try it at work.

Share this post


Link to post
Share on other sites

,,,well Irg, but for which frequency do you want...!!!

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!


Register a new account

Sign in

Already have an account? Sign in here.


Sign In Now